Xilinx LogiCORE IP Product Manual Download Page 32

Page: 32 / 142

XAUI v12.3 Product Guide

www.xilinx.com

PG053 April 6, 2016

Chapter 2:

Product Specification

Configuration and Status Signals

The Configuration and Status Signals are shown in

Table 2-11

. See

Configuration and Status

Interfaces

for more information on these signals, including a breakdown of the

configuration and status vectors.

Clocking and Reset Signals and Module

Included in the example design top-level sources are circuits for clock and reset

management. These can include Digital Clock Managers (DCMs), Mixed-Mode Clock

Managers (MMCMs), reset synchronizers, or other useful utility circuits that might be useful

in your particular application.

mdio_out

out

clk156_out

MDIO output

mdio_tri

out

clk156_out

MDIO 3-state; ‘1’ disconnects the output driver from the MDIO

bus.

type_sel[1:0]

Tie-off

Type select

prtad[4:0]

Tie-off

MDIO port address; you should set this to provide a unique ID

on the MDIO bus.

Table 2

‐

10:

MDIO Management Interface Ports

(Cont’d)

Signal Name

Direction

Clock
Domain

Description

Table 2

‐

11:

Configuration and Status Ports

Signal Name

Direction

Clock
Domain

Description

configuration_ vector[6:0] in

clk156_out

Configuration information for the core.

status_vector[7:0]

out

clk156_out

Status information from the core.

debug[5]

out

clk156_out

align_status: 1 when the XAUI receiver is

aligned across all four lanes, 0 otherwise.

debug[4:1]

out

clk156_out

sync_status: Each pin is 1 when the respective

XAUI lane receiver is synchronized to byte

boundaries, 0 otherwise.

debug[0]

out

clk156_out

Indicates when the TX phase alignment of the

transceiver has been completed.

Send Feedback

Summary of Contents for LogiCORE IP















































































































































Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands

Xilinx LogiCORE IP, Product Manual

Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands