manualshive.com logo in svg

Xilinx LogiCORE IP, Product Manual

Share
Download
Xilinx LogiCORE IP Product Manual Download Page 17

XAUI v12.3 Product Guide

www.xilinx.com

17

PG053 April 6, 2016

Chapter 2:

Product Specification

Transceiver Control and Status Ports

Optional ports that, if enabled, allow the monitoring and control of certain important ports 

of the transceivers. When not selected, these ports are tied to their default values. For 

information on these ports, see the 

7 Series FPGAs GTX/GTH Transceivers User Guide 

(UG476) 

[Ref 1]

, the 

7 Series FPGAs GTP Transceivers User Guide 

(UG482) 

[Ref 2]

, the 

UltraScale Architecture GTH Transceivers User Guide

 (UG576) 

[Ref 3]

, and the 

Ultrascale 

Architecture GTY Transceivers User Guide

 (UG578) 

[Ref 4]

).

IMPORTANT:

The ports in the Transceiver Control And Status Interface must be driven in accordance 

with the appropriate GT user guide. Using the input signals listed in 

Table 2-8

 may result in 

unpredictable behavior of the IP core.

Note:

The Dynamic Reconfiguration Port is only available if the Transceiver Control and Status Ports 

option is selected

Table 2

‐

8:

Transceiver Control and Status Ports —7 Series FPGAs

Signal Name

Direction

Clock 
Domain

Description

CHANNEL 0

GT0 DRP

gt0_drpaddr[8:0]

in

dclk

DRP address bus for channel 0

gt0_drpen

in

dclk

DRP enable signal. 

0: No read or write operation performed. 

1: enables a read or write operation.

gt0_drpdi[15:0]

in

dclk

Data bus for writing configuration data to the 

transceiver for channel 0.

gt0_drpdo[15:0]

out

dclk

Data bus for reading configuration data from the 

transceiver for channel 0.

gt0_drprdy

out

dclk

Indicates operation is complete for write operations 

and data is valid for read operations for channel 0.

gt0_drpwe

in

dclk

DRP write enable for channel 0. 

0: Read operation when drpen is 1. 

1: Write operation when drpen is 1.

gt0_drp_busy

out

dclk

(GTPE2 all configurations or GTHE2 10G 

configuration). Indicates the DRP interface is being 

used internally by the serial transceiver and should not 

be driven until this signal is deasserted.

GT0 TX Reset and Initialization

gt0_txpmareset_in

in

Async

Starts the TX PMA reset process.

gt0_txpcsreset_in

in

Async

Starts the TX PCS reset process.

gt0_txresetdone_out

out

clk156_out When asserted the serial transceiver TX has finished 

reset and is ready for use.

Send Feedback

Summary of Contents for LogiCORE IP















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands