Xilinx LogiCORE IP Product Manual Download Page 119

Page: 119 / 142

XAUI v12.3 Product Guide

www.xilinx.com

119

PG053 April 6, 2016

Appendix A

Verification and Interoperability

The XAUI core has been verified using both simulation and hardware testing.

Simulation

A highly parameterizable transaction-based simulation test suite has been used to verify

the core. Tests included:

• Register access over MDIO
• Loss and re-gain of synchronization
• Loss and re-gain of alignment
• Frame transmission
• Frame reception
• Clock compensation
• Recovery from error conditions

Hardware Testing

The core has been used in several hardware test platforms within Xilinx. In particular, the

core has been used in a test platform design with the Xilinx

10-Gigabit Ethernet MAC core.

This design comprises the MAC, XAUI, a “ping” loopback FIFO, and a test pattern generator

all under embedded PowerPC® processor control. This design has been used for

conformance and interoperability testing at the University of New Hampshire

Interoperability Lab. PCS reports are available from the factory on request.

Send Feedback

Summary of Contents for LogiCORE IP















































































































































Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands

Xilinx LogiCORE IP, Product Manual

Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands