manualshive.com logo in svg

Xilinx LogiCORE IP, Product Manual, Page: 22 / 142

Share
Download
Xilinx LogiCORE IP Product Manual Download Page 22

XAUI v12.3 Product Guide

www.xilinx.com

22

PG053 April 6, 2016

Chapter 2:

Product Specification

GT1 TX Driver

gt1_txpostcursor_in[4:0]

in

Async

Transmitter post-cursor TX post-emphasis control.

gt1_txprecursor_in[4:0]

in

Async

Transmitter post-cursor TX pre-emphasis control.

gt1_txdiffctrl_in[3:0]

in

Async

Driver Swing Control.

gt1_txinhibit_in

in

clk156_out When High, this signal blocks the transmission of data.

GT1 PRBS

gt1_rxprbscntreset_in

in

clk156_out Resets the PRBS error counter.

gt1_rxprbserr_out

out

clk156_out This non-sticky status output indicates that PRBS 

errors have occurred.

gt1_rxprbssel_in[2:0]

in

clk156_out Receiver PRBS checker test pattern control.

gt1_txprbssel_in[2:0]

in

clk156_out Transmitter PRBS generator test pattern control.

gt1_txprbsforceerr_in

in

clk156_out

When this port is driven High, errors are forced in the 

PRBS transmitter. While this port is asserted, the 

output data pattern contains errors.

GT1 RX CDR

gt1_rxcdrhold_in

in

Async

Hold the CDR control loop frozen.

GT1 Digital Monitor

gt1_dmonitorout_out[7:0]

out

Async

(GTXE2) Digital Monitor Output Bus

gt1_dmonitorout_out[14:0]

out

Async

(GTHE2) Digital Monitor Output Bus

gt1_dmonitorout_out[14:0]

out

Async

(GTPE2) Digital Monitor Output Bus

GT1 Status

gt1_rxdisperr_out[3:0]

out

clk156_out Active-High indicates the corresponding byte of the 

received data has a disparity error

gt1_rxnotintable_out[3:0]

out

clk156_out

Active-High indicates the corresponding byte of the 

received data was not a valid character in the 8B/10B 

table.

gt1_rxcommadet_out

out

clk156_out This signal is asserted when the comma alignment 

block detects a comma.

CHANNEL 2

GT2 DRP

gt2_drpaddr[8:0]

in

dclk

DRP address bus for channel 2.

gt2_drpen

in

dclk

DRP enable signal. 
0: No read or write operation performed. 
1: enables a read or write operation.

gt2_drpdi[15:0]

in

dclk

Data bus for writing configuration data to the 

transceiver for channel 2.

Table 2

‐

8:

Transceiver Control and Status Ports —7 Series FPGAs 

(Cont’d)

Signal Name

Direction

Clock 
Domain

Description

Send Feedback

Summary of Contents for LogiCORE IP















































































































































Reviews:

No comments