Xilinx LogiCORE IP Product Manual Download Page 84

Page: 84 / 142

XAUI v12.3 Product Guide

www.xilinx.com

PG053 April 6, 2016

Chapter 5:

Interfacing to the Core

The

type_sel

port is registered into the core at FPGA configuration and core hard reset;

changes after that time are ignored by the core.

Table 5-4

shows the mapping of the

type_sel

setting to the implemented register map.

The

prtad[4:0]

port sets the port address of the core instance. Multiple instances of the

same core can be supported on the same MDIO bus by setting

prtad[4:0]

to a unique

value for each instance; the XAUI core ignores transactions with the PRTAD field set to a

value other than that on its

prtad[4:0]

port.

MDIO Transactions

The MDIO interface should be driven from a STA master according to the protocol defined

IEEE Std. 802.3-2012

. An outline of each transaction type is described in the following

sections. In these sections, the following abbreviations apply:

• PRE:  preamble
• ST:  start
• OP:  operation  code
• PRTAD:  port  address
• DEVAD: device address
• TA: turnaround

Table 5

‐

Mapping of type_sel Port Settings to MDIO Register Type

type_sel setting

MDIO Register

Description

00 or 01

10GBASE-X PCS/PMA

When driving a 10GBASE-X PHY

Data Terminal Equipment

(DTE)

XGMII Extender Sublayer

(XGXS)

When connected to a 10GMAC through XGMII

PHY XGXS

When connected to a PHY through XGMII

Send Feedback

Summary of Contents for LogiCORE IP















































































































































Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands

Xilinx LogiCORE IP, Product Manual

Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands