manualshive.com logo in svg

WAGO 852-1305, Manual

Share
Download
WAGO 852-1305 Manual Download Page 77

WAGO-ETHERNET-Zubehör 852 

Enhanced Features 

77 

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 

 

 

Manual 

 

1.1.0  

 

 

Figure 18: Application 1 (via a Router) 

 

•

 

Application 2 (local in different VLANs)

 

 

DHCP client 1 and DHCP client 2 are in different VLANs. However, they 

receive IP address from the same DHCP server. 

 

 

Figure 19: Application 2 (Local in Different VLANs) 

 

VLAN 1:  

Port 1, 2 (Management VLAN) 

VLAN 2:  

Port 3, 4 

VLAN 3:  

Port 5, 6 

VLAN 4:  

Port 7, 8 

DHCP Server -> Port 1. 

DHCP Client -> Port 2, 3, 4, 5, 6, 7, 8. 

Result:    

Hosts connected to port 2, 3, 4, 5, 6, 7 and 8 receive an IP from 

   

 

the DHCP server. 

 

 

 

DHCP Server Connection 

The DHCP server must be connected to the subscriber ports of the management 

VLAN. 

The “DHCP Relay” in the management VLAN must be enabled. 

Summary of Contents for 852-1305



























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands