WAGO 852-1305 Manual Download Page 144

Page: 144 / 314

144 Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

9.3.1.2.2 Bandwidth Limitation

Additional Information

Please refer to the section “Function Description” for more information on

“Bandwidth Limitation”.

Figure 44: WBM “Rate Limitation” Page – “Bandwidth Limitation” Tab

Table 48: WBM “Rate Limitation” Page – “Bandwidth Limitation” Tab

Bandwidth Limitation Settings
Parameters

Default

Description

Port

From:

Select a port or port range in the selection box to

configure the “Rate Limitation Settings”.

to:

Select a port or port range in the selection box to

configure the “Rate Limitation Settings”.

Ingress (Mbs)

Enter the “Rate Limitation” for incoming packets in

the input field.

Port 1 … 8 0 … 100

Port 9 … 10 0 … 1000

Egress (Mbs)

Enter the “Rate Limitation” for outgoing packets in

the input field.

Bandwidth Limitation Status
Parameters

Default

Description

Port

1 … 10

This column displays the port numbers.

Ingress (Mbs)

This column displays the bandwidth set for

“Ingress”.

Egress (Mbs)

This column displays the bandwidth set for

“Egress”.

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands