Home
/
WAGO
/
852-1305
/
Manual

WAGO 852-1305, Manual

Share

Page: 41 / 314

WAGO 852-1305 Manual Download Page 41

WAGO-ETHERNET-Zubehör 852

Connect Devices

41

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Pos: 24.6 /Serie 852 (ETH ERNET-Zubehör)/Anschließ en/Anschluss 1000Base- SX/LX, Glasfaser kabel 852- x30x @ 24\mod_1452260347709_21.docx @ 197927 @ 2 @ 1

6.4

1000Base-SX/LX Port, Fiber Optic

When connecting a fiber optic cable to a 1000Base-SX/LX port on the industrial

managed switch, make sure to use the right connector type (LC) and SFP module.

There are various types of multi-mode, single mode or WDM SFP modules.

Follow the steps below to connect the fiber optic cable properly:

Rubber covers

Remove and safely store the rubber covers of the fiber optic port (LC).

If no fiber optic cable is connected, the rubber cover should be installed to protect

the fiber optics.

1

Insert the respective SFP modules.

2

Ensure that the fiber optic ports are clean. You can clean the cable

connectors by wiping them with a clean cloth or a cotton ball soaked with a

little ethanol. Dirty fiber optic cables affect the quality of the light

transmitted via the cable and leads to reduced performance at the port.

3

Connect one end of the fiber optic cable to the LC port of the industrial

managed switch and the other end to the fiber optic port of the other device.

Proper connection of the fiber optic cable to the SFP module

For a proper connection, snap the connector of the fiber optic cable into the SFP

module audibly.

4

Check the respective port LED on the industrial managed switch that the

connection is established (see section “Device Description” > … > “Display

Elements”).

Pos: 24.7 /Dokumentation allgemei n/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

«
...
39
40
41
42
43
...
»

Summary of Contents for 852-1305



























































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands