WAGO 852-1305 Manual Download Page 116

Page: 116 / 314

116 Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

You can access the respective WBM pages via the links in the navigation bar:

Table 29: Overview - Navigation Links and WBM Pages

Navigation Links and WBM Pages



[System Status]

•

System Information



[Basic Settings]

•

General Settings

•

MAC Management

•

Port Mirroring

•

Port Settings



[Advanced Settings]



[Bandwidth Control]

•

QoS

•

Rate Limitation

[IMGP Snooping]



•

IGMP Snooping

•

IGMP Filtering

•

MVR

•

Multicast Addr.

•

Multicast IP Statistics

[VLAN]



•

Port Isolation

•

VLAN

•

GVRP

•

MAC VLAN

•

Protocol VLAN

•

Q-in-Q

•

DHCP Relay

•

DHCP Options

•

Dual Homing

•

Dual Ring

•

ERPS

•

Link Aggregation

•

LLDP

•

Loop Detection

•

Jet Ring

•

Modbus

•

STP

•

Xpress Ring

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands