WAGO 852-1305 Manual Download Page 65

Page: 65 / 314

WAGO-ETHERNET-Zubehör 852

Enhanced Features

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Figure 15: Multicast Address

Table 19: IP Multicast Addresses

IP multicast address Description

224.0.0.0

Base address (reserved)

224.0.0.1

“All Hosts Multicast” group that contains all systems on

the same network segment.

224.0.0.2

“All Routers Multicast” group that contains all routers on

the same network segment.

224.0.0.5

The “Open Shortest Path First” (OSPF protocol), the

“AllSPFRouters” address. Used to send “Hello Packets”

to all OSPF routers on a network segment

224.0.0.6

The “OSPF AllDRouters” address. Used to send OSPF

routing information to “OSPF Designated Routers” on a

network segment

224.0.0.9

The RIP (“Routing Information Protocol”) Version 2 of

the group address. Used to send routing information to all

RIPv2-compatible routers on a network segment.

224.0.0.10

The EIGRP group address. Used to send EIGRP routing

information to all EIGRP routers on a network segment.

224.0.0.13

PIM Version 2 (“Protocol Independent Multicast”)

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands