manualshive.com logo in svg

WAGO 852-1305, Manual

Share
Download
WAGO 852-1305 Manual Download Page 275

WAGO-ETHERNET-Zubehör 852 

Appendix  275 

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 

 

 

Manual 

 

1.1.0  

 

10.3.3.12  Dual Homing 

Table 134: CLI “Dual Homing” Configuration 

Node 

Command 

Description 

enable 

show dual-homing 

This command displays the “Dual Homing” 

information. 

configure 

dual-homing  (disable | 

enable) 

This command disables / enables the “Dual Homing” 

function in the system. 

configure 

no dual-homing primary-

channel 

This command deletes the primary channel for “Dual 

Homing” from the system. 

configure 

no dual-homing primary-

channel 

This command deletes the primary channel for “Dual 

Homing” from the system. 

configure 

dual-homing secondary-

channel (port | trunk) 

VALUE 

This command configures the secondary channel for 

“Dual Homing” in the system. The channel can be a 

single port or a “Trunk Group”. 

configure 

no dual-homing 

secondary-channel 

This command deletes the secondary channel for 

“Dual Homing” from the system. 

 

Example

 

L2SWITCH(config)# 

link-aggregation 1 ports 5-6 

L2SWITCH(config)# 

link-aggregation 1 enable 

L2SWITCH(config)# 

dual-homing primary-channel port 2 

L2SWITCH(config)# 

dual-homing secondary -channel trunk 1 

L2SWITCH(config)# 

dual-homing enable 

 

10.3.3.13  Link Aggregation 

Table 135: CLI “Link Aggregation” Configuration 

Node 

Command 

Description 

enable 

show link-aggregation 

The command displays the current configuration for 

“Trunking”. 

configure 

link-aggregation 

[GROUP_ID] (disable | 

enable) 

The command disables / enables “Trunking” for the 

specific “Trunk Group”. 

configure 

link-aggregation 

[GROUP_ID] interface 

PORTLISTS 

The command adds ports to a specific “Trunk 

Group”. 

configure 

no link-aggregation 

[GROUP_ID] interface 

PORTLISTS 

The command deletes ports from a specific “Trunk 

Group”. 

 

Summary of Contents for 852-1305



























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands