WAGO 852-1305 Manual Download Page 269

Page: 269 / 314

WAGO-ETHERNET-Zubehör 852

Appendix 269

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

10.3.3.6 MVR

Table 127: CLI “MVR” Configuration

Node

Command

Description

enable

show mvr

This command displays the current MVR

configurations.

enable

show mvr vlan VLANID This command displays the current MVR

configurations of the specific VLAN.

enable

show igmp-snooping

This command displays the current “IGMP

Snooping” configurations.

configure

mvr VLANID

This command creates the MVR configurations for

the specific VLAN.

configure

no mvr VLANID

This command disables the MVR configurations for

the specific VLAN.

MVR

group NAME

This command creates a group configuration for the

MVR.

MVR

no group NAME

This command deletes the group configurations from

the MVR.

MVR

inactive

This command disables the MVR settings.

MVR

no inactive

This command enables the MVR settings.

MVR

mode (dynamic |

compatible)

This command configures the mode for the MVR.

- Dynamic: Sends “IGMP Reports” to

all MVR source ports in the

multicast VLAN.

- Compatibility: The switch does not send any

“IGMP Reports”.

MVR

name STRING

This command configures the name for the MVR.

MVR

no name

This command configures the default name for the

MVR.

MVR

receiver-port PORTLIST This command assigns a receiver port or receiver

port range. Normally, the source ports are connected

to the “Streaming Client”.

MVR

no receiver-port

PORTLIST

This command deletes a port or port range from the

list of receiver ports.

MVR

source-port PORTLIST

This command assigns a source port or source port

range. Normally, the source ports are connected to

the “Streaming Server”.

MVR

no source-port PORTLIST This command deletes a port or port range from the

list of source ports.

MVR

tagged PORTLIST

This command assigns a tagged port or port range.

The same applies to VLAN tagged ports.

MVR

no tagged PORTLIST

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands