WAGO 852-1305 Manual Download Page 117

Page: 117 / 314

WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 117

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0



[Security]

[IP Source Guard]



•

DHCP Snooping

•

Binding Table

•

ARP Inspection

•

Access Control List

•

802.1x

•

Port Security



[Monitor]

•

Alarm

•

Monitor Information

•

Port Statistics

•

Port Utilization

•

RMON Statistics

•

SFP Information

•

Traffic Monitor



[Management]

[SNMP]



•

SNMP

•

SNMP Trap

•

Auto Provision

•

Mail Alarm

•

Maintenance

•

System Log

•

User Account

The settings/configuration of the industrial managed switch can be made on these

WBM pages.

There are tab pages on some WBM pages for the settings/configuration.

The default values are displayed in

bold

Pos: 28.8.2 /Serie 852 (ETH ERNET-Z ubehör)/Konfigurieren/System Status 852- 1305 @ 27\mod_1467636056072_21.docx @ 215998 @ 23 @ 1

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands