WAGO 852-1305 Manual Download Page 107

Page: 107 / 314

WAGO-ETHERNET-Zubehör 852

Enhanced Features 107

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

7.4.4.1 DDM

DDM (“

ynamic

evice

apping”) is a technology for KVM switches with USB

ports that are sometimes used as an alternative to standard USB keyboard and

mouse emulation.

7.4.5

Traffic Monitor

The “Traffic Monitor” function can be used to enable or disable a specific port or

the switch globally. The function can monitor the data rate of broadcast, multicast

or broadcast and multicast packets. If the packet rate exceeds the specification for

a user, the port is blocked. If the “Recovery” function is enabled, the port is

enabled again after the “Recovery Time” has expired.

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

WAGO 852-1305, Manual, Page: 107 / 314

Search results

Summary of Contents for 852-1305

Reviews: