manualshive.com logo in svg

WAGO 852-1305, Manual

Share
Download
WAGO 852-1305 Manual Download Page 160

160  Configuring in the Web-Based Management System (WBM)  WAGO-ETHERNET-Zubehör 852 

 

 

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 

 

Manual 

 

1.1.0  

9.3.3.2  VLAN 

9.3.3.2.1  VLAN Settings 

 

Figure 56: WBM “VLAN” Page – “VLAN Settings” Tab 

 

Table 60: WBM “VLAN” Page – “VLAN Settings” Tab 

VLAN Settings 
Parameters 

Default 

Description 

VLAN ID  From: 

 

Enter the VLAN ID for this entry in the input field. 

Valid range: 1 … 4094 

To: 

 

Enter the VLAN ID for this entry in the input field. 

Valid range: 1 … 4094 

VLAN Name 

 

Enter a descriptive name for the VLAN for 

identification purposes. 

The VLAN name should be a combination of 

numbers, letters, hyphens (-) or underscores (_). 

Member Port 

 

Enter the port numbers that the switch should assign 

to the VLAN as subscribers. You can specify 

multiple individual port numbers or ranges by using 

a comma (,) to separate individual ports or using a 

hyphen (-) for port ranges. 

Summary of Contents for 852-1305



























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands