manualshive.com logo in svg

WAGO 852-1305, Manual

Share
Download
WAGO 852-1305 Manual Download Page 43

WAGO-ETHERNET-Zubehör 852 

Enhanced Features 

43 

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 

 

 

Manual 

 

1.1.0  

 

Pos:  26.1 /Serie 852 (ETH ERNET-Zubehör)/Er wei terte F unkti onen/F unktionsbeschr eibung - Ü berschrift 1 @ 3\mod_1222693989093_21.docx @ 22350  @  1 @ 1 

 

7 

Enhanced Features 

Pos:  26.2 /Serie 852 (ETH ERNET-Zubehör)/Er wei terte F unkti onen/F unktionsbeschr eibung 852- x30x @ 26\mod_1465377409507_21.docx @ 212038 @ 23333443323445534434445533333344333332345445333233334323333 @ 1 

 

7.1 

Default Settings 

7.1.1 

Jumbo Frame 

“Jumbo Frames” are ETHERNET frames with a size of more than 1500 bytes. 

Jumbo frames can increase data transmission efficiency in a network. The bigger 

the “Jumbo Frame”, the better the network performance. 

 

 

 

“Jumbo Frame” settings 

The “Jumbo Frame” settings apply to all ports. 

 

If the size of a packet exceeds the size of the “Jumbo Frame”, the packet is 

dropped. 

7.1.2 

SNTP 

SNTP (“

S

imple 

N

etwork 

T

ime 

P

rotocol”) is a protocol for synchronizing clocks 

in computer systems. It is a less complex implementation of an NTP (“

N

etwork 

T

ime 

P

rotocol”). 

 

SNTP uses “

C

oordinated 

U

niversal 

T

ime” (French: “

T

emps 

U

niversel 

C

oordonné”). No information on time zones or daylight savings time is 

transmitted. This information falls outside the protocol range and must be 

obtained separately. 

The SNTP port is 123. 

 

 

 

1. 

The SNTP server always replies the current UTC time. 

2. 

If the switch receives the SNTP reply time, it adjusts the time to the time 

 

zone configuration and configures the time for the switch accordingly. 

3. 

If the time server's IP address is not configured, the switch does not send 

 

an SNTP request packet. 

4. 

If the switch does not receive an SNTP reply packet, it repeats the 

 

challenge indefinitely every ten seconds. 

5. 

If the switch receives an SNTP reply, it repeats the time request from the 

 

NTP server every hour. 

6. 

If the time zone and NTP server changes, the switch repeats the request 

 

process. 

7. 

No default SNTP server. 

 

 

 

Summary of Contents for 852-1305



























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands