WAGO 852-1305 Manual Download Page 66

Page: 66 / 314

Enhanced Features

WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Table 19: IP Multicast Addresses

IP multicast address Description

224.0.0.18

Virtual Router Redundancy Protocol

224.0.0.19 - 21

IS-IS over IP

224.0.0.22

IGMP Version 3 (“Internet Group Management

Protocol”)

224.0.0.102

Hot Standby Router Protocol Version 2

224.0.0.251

Multicast DNS address

224.0.0.252

“Link-local Multicast Name Resolution”-address

224.0.1.1

“Network Time Protocol” address

224.0.1.39

“Cisco Auto-RP-Announce” address

224.0.1.40

“Cisco Auto-RP-Discovery” address

224.0.1.41

“H.323 Gatekeeper Discovery” address

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

WAGO 852-1305, Manual, Page: 66 / 314

Search results

Summary of Contents for 852-1305

Reviews: