manualshive.com logo in svg

WAGO 852-1305, Manual

Share
Download
WAGO 852-1305 Manual Download Page 132

132  Configuring in the Web-Based Management System (WBM)  WAGO-ETHERNET-Zubehör 852 

 

 

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 

 

Manual 

 

1.1.0  

9.2.3 

Port Mirroring 

 

 

 

Additional Information 

Please refer to the section “Function Description” for more information on “Port 

Mirroring”. 

 

 

 

 

Monitor Port 

The monitor port cannot be a member of any “Truck Port” group. 

The monitor port cannot be an ingress or egress port. 

If a port has been configured as a source port and a user then configures it as a 

destination port, the port is automatically deleted from the source ports. 

 

 

 

Figure 36: WBM “Port Mirroring” Page 

 

 

Summary of Contents for 852-1305



























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands