WAGO 852-1305 Manual Download Page 168

Page: 168 / 314

168 Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Table 64: WBM “GARP VLAN Registration Protocol” Page – “GVRP Timer” Tab

GARP Timer Settings
Parameters

Default

Description

Port

From:

Select a port or port range in the selection box to

configure the GARP timer.

To:

Select a port or port range in the selection box to

configure the GARP timer.

Join Time

Enter the maximum time in milliseconds that the

interface waits before sending VLAN messages.

Leave Time

Enter the maximum time in milliseconds that the

interface waits after receiving a “Leave Message”

before the interface leaves the VLAN specified in

the message.

Leave All Time

1000

Enter the time interval in milliseconds after which

the Leave All messages are sent to interfaces. Leave

All messages can help to update information about

current GVRP VLAN subscriber information in the

network.

GARP Timer Status
Parameters

Default

Description

Port

1 … 10

This column displays the port numbers.

Join Time

This column displays the Join Time.

Hold Time

This column displays the Hold Time.

Leave Time

This column displays the Leave Time.

Leave All Time

This column displays the Leave All Time.

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands