WAGO 852-1305 Manual Download Page 38

Page: 38 / 314

Mounting

WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Pos: 21.1 /All e Seri en ( Allgemei ne Module)/Ü berschriften/Ebene 1/M ontier en - Ü berschrift 1 @ 3\mod_1225446744750_21.docx @ 24900 @ 1 @ 1

Mounting

Pos: 21.2 /Serie 852 (ETH ERNET-Zubehör)/Montier en/Montageort 852- x30x @ 24\mod_1452256541388_21.docx @ 197891 @ 2 @ 1

5.1

Installation Site

The location selected to install the industrial managed switch may greatly affect

its performance. When selecting a site, we recommend considering the following

rules:

•

Install the industrial managed switch at an appropriate place. See section

“Device Description” > … > “Technical Data“ for the acceptable

temperature and humidity operating ranges.

Pos: 21.3 /Serie 852 (ETH ERNET-Zubehör)/Montier en/Monti eren 852- x30x @ 24\mod_1452258998917_21.docx @ 197895 @ 22 @ 1

Make sure that the heat output from the industrial managed switch and ventilation

around it is adequate. Do not place any heavy objects on the industrial managed

switch.

5.2

Installation on a Carrier Rail

The carrier rail must optimally support the EMC measures integrated into the

system and the shielding of the internal data bus connections.

Place the industrial managed switch onto the DIN rail from the top and snap it

into position.

5.3

Removal from Carrier ail

To remove the industrial managed switch from the carrier rail, insert a suitable

tool into the metal tab under the switch and deflect the metal tab downward.

You can then release the switch down from the carrier rail and remove it upwards.

Pos: 22 /D okumentation allgemei n/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands