WAGO 852-1305 Manual Download Page 244

Page: 244 / 314

244 Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Table 107: WBM Page, “SNMP” – “Community Name” Tab

Community Name List
Parameters

Default

Description

No.

This column displays the “Community” number. It is

used for identification only.

Click a number to modify the setting for a specific

“Community”.

Community String

This column displays the “SNMP Community

String”.

This is a text element that acts as a password.

Rights

This column displays the rights for the “SNMP

Community String”.

Network ID of Trusted

Host

This column displays the IP address of the remote

SNMP management station after it has been

modified by the subnet mask.

Mask

This column displays the subnet mask for the IP

address of the remote SNMP management station.

Action

Click

[Delete]

to delete a specific “Community

String”.

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands