WAGO 852-1305 Manual Download Page 111

Page: 111 / 314

WAGO-ETHERNET-Zubehör 852

Enhanced Features 111

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

7.5.4

Mail Alarm

The “Mail Alarm” function sends an e-mail trap to a previously defined

administrator when certain events occur. The events are listed below:

System Reboot:

The system performs a warm or cold start.

Port Link Change:

A port connection is established or fails.

Configuration Change:

The system configurations in the

NV-RAM have been updated.

Firmware Upgrade:

The system firmware has been updated.

User Login:

A user has logged into the system.

Port Blocked:

A port is blocked by “Loop Detection” or

“BPDU Guard”.

Pos: 27 /D okumentation allgemei n/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands