WAGO 852-1305 Manual Download Page 230

Page: 230 / 314

230 Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Pos: 28.8.7 /Serie 852 (ETH ERNET-Z ubehör)/Konfigurieren/M oni tor 852- 0303 @ 27\mod_1468312186200_21.docx @ 216538 @ 23333333 @ 1

Monitor

9.5

Monitor

9.5.1

Alarm Information

Additional Information

Please refer to the section “Function Description” for more information on the

“Alarm”.

Figure 95: WBM “Alarm Information” Page

Table 99: WBM “Alarm Information” Page

Alarm Information
Parameters

Default

Description

Alarm Status

This display field shows if there are any alarm

events.

Alarm Reason(s)

This display field shows details about the alarm

events.

Port

0 … 10

PWR

RPS

This column displays the DIP switch name.

DIP switch settings

Enable

Disable

This column displays the current status of the DIP

switch.

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands