WAGO 852-1305 Manual Download Page 24

Page: 24 / 314

Device Description

WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Table 3: Legend for the Figure “Front View of the Industrial Managed Switch”

No. Descrip-

tion

Meaning

For Details see Section

SFP

SFP port LNK/ACT (4)

“Device Description” >

“Display Elements”

Reset

Reset button

"Device Description" >

"Operating Elements"

Status LED TX Port 100 Mbit/s

(1 LED for each port)

“Device Description” >

“Display Elements”

Status LED TX Port LNK/ACT

(1 LED for each port)

“Device Description” >

“Display Elements”

Port 1 x RJ-45 (RS-232 port switch)

"Device Description" >

"Connections"

Port 8 x RJ-45 (10/100/1000BASE-T ports)

"Device Description" >

"Connections"

Port 4 x SFP (1000BASE-SX/LX, fiber optic)

"Device Description" >

"Connections"

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands