WAGO 852-1305 Manual Download Page 157

Page: 157 / 314

WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 157

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

9.3.2.5 Multicast IP Statistics

Figure 54: WBM “Multicast IP Statistics” Page

Table 58: WBM “Multicast IP Statistics” Page

Multicast IP Table
Parameters

Default

Description

Index

1 … 10

This column displays the number of entries.

Port

1 … 10

This column displays the port number.

Multicast Group

This column displays the IP address of the multicast

group.

VID

This column displays the VLAN ID.

Timeout

This column displays the timeout time.

Explicit Tracking

This column displays if “Explicit Tracking” is set.

Host IP

This column displays the host IP.

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands