manualshive.com logo in svg

WAGO 852-1305, Manual

Share
Download
WAGO 852-1305 Manual Download Page 166

166  Configuring in the Web-Based Management System (WBM)  WAGO-ETHERNET-Zubehör 852 

 

 

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 

 

Manual 

 

1.1.0  

Table 63: WBM “GARP VLAN Registration Protocol” Page – “GVRP” Tab 

GVRP Settings 
Parameters 

Default 

Description 

GVRP State 

Disable 

Select “Disable” in the selection box to disable the 

GVRP function. 

Enable 

Select “Enable” in the selection box to enable the 

GVRP function and to exchange the VLAN 

configuration information with other GVRP 

switches. 

Port  

From: 

1 

Select a port or port range in the selection box to 

configure the GVRP settings. 

To: 

1 

Select a port or port range in the selection box to 

configure the GVRP settings. 

State 

Disable 

Select “Disable” in the selection box to disable the 

GVRP function for the port. 

Enable 

Select “Enable” in the selection box to enable the 

GVRP function for the port. 

Registration Mode 

Normal 

Select “Normal” in the selection box to allow 

dynamic creation (if dynamic VLAN creation is 

enabled), registration and deregistration of VLANs 

on the trunk port. 

Forbidden 

Select “Forbidden” in the selection box to deregister 

all VLANs (except VLAN 1) and to prevent any 

further creation or deregistration of VLANs on the 

“Trunk Port”. 

GVRP Status 
Parameters 

Default 

Description 

Port 

1 … 10 

This column displays the port numbers. 

State 

Disable 

Enable 

This column displays the set status. 

Registration Mode 

Normal 

Forbidden 

This column displays the selected registration mode. 

 

 

 

Summary of Contents for 852-1305



























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands