WAGO 852-1305 Manual Download Page 203

Page: 203 / 314

WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 203

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Table 85: WBM “STP” Page – “Port Parameters” Tab

Port Status
Parameters

Default

Description

Port

1 … 10

This column displays the port numbers.

Active

Enable

Disable

This column displays the status of the STP function.

Role

Alternated

Designated

Root

Backup

None

This column displays the role of the port.

Status

Discarding

Blocking

Listening

Learning

Forwarding

Disabled

This column displays the port status.

Path Cost

0 … 65535

This column displays the path cost of the port.

Priority

0 … 61440

This column displays the port priority.

Edge Port

Disable

Enable

This column displays the status of the “Edge Port”

function.

BPDU Filter

Disable

Enable

This column displays the status of the BPDU filter

function.

BPDU Guard

Disable

Enable

This column displays the status of the “BPDU

Guard” function.

ROOT Guard

Disable

Enable

This column displays the status of the “Root Guard”

function.

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands