manualshive.com logo in svg

WAGO 852-1305, Manual

Share
Download
WAGO 852-1305 Manual Download Page 15

WAGO-ETHERNET-Zubehör 852 

Important Notes 

15 

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 

 

 

Manual 

 

1.1.0  

 

Pos:  14.8 /Serie 852 (ETH ERNET-Zubehör)/Wichtige Erl äuter ungen/N or men und Richtlinien 852- xxxx - Ü berschrift 2 und Inhalt @ 3\mod_1222346239453_21.docx @  22261 @ 3 @  1 

 

2.1.5 

Standards and Regulations for Operating the Industrial 

Switches 

Please observe the standards and regulations that are relevant to installation: 

•

 

The data and power lines must be connected and installed in compliance 

with the standards to avoid failures on your installation and eliminate any 

danger to personnel. 

•

 

For installation, startup, maintenance and repair, please observe the accident 

prevention regulations of your machine (e.g., BGV A 3, “Electrical 

Installations and Equipment”). 

•

 

Emergency stop functions and equipment must not be deactivated or 

otherwise made ineffective. See relevant standards (e.g., DIN EN 418). 

•

 

Your installation must be equipped in accordance to the EMC guidelines so 

electromagnetic interferences can be eliminated. 

•

 

Please observe the safety measures against electrostatic discharge according 

to DIN EN 61340-5-1/-3. When handling the modules, ensure that 

environmental factors (persons, workplace and packing) are well grounded. 

•

 

The relevant valid and applicable standards and guidelines regarding the 

installation of switch cabinets must be observed. 

Pos: 14.9 /Dokumentation  allgemei n/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810  @   @  1 

 

 

 

Summary of Contents for 852-1305



























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands