WAGO 852-1305 Manual Download Page 114

Page: 114 / 314

114 Configuration

WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Pos: 28.6 /Serie 852 (ETH ERNET-Zubehör)/Konfigurieren/Konsolenport @ 25\mod_1453203786134_21.docx @ 198615 @ 3 @ 1

8.1.2

Console Port

Before accessing the integrated management agent of the industrial managed

switch via a network connection, you first have to configure it via a local

connection or the BOOTP protocol with the default IP address, a subnet mask and

a standard gateway.

After configuring the IP parameters of the industrial managed switch, you can

access the integrated configuration utility from any point in the connected

network or via the Internet. The integrated configuration utility can be called up

via Telnet from any computer connected to the network. In addition, it can be

managed from any computer via a Web browser.

Connect the computer to the console port on the switch using the

appropriate cable.

Use Telnet with the following settings:

Table 27: Default Settings for the Console Port

Setting

Default Value

Terminal Emulation

VT100

Baud Rate

38400

Parity

None

Number of Data Bits

Number of Stop Bits

Flow Control

None

Press [ENTER] to open the login screen.

Table 28: Login Screen

Setting

Default Value

FW Version 01

FW Version 02 or

higher

Default Username

admin

Default Password

Wago1951

wago

Requirement to establish the connection

Make sure that the terminal or PC is configured for the connection with the above

settings. Otherwise, no connection can be established.

Please refer to the section “Appendix” > … > “RJ-45 Cable” for details on the

cable terminal assignment.

Pos: 28.7 /Dokumentation allgemei n/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands