WAGO 852-1305 Manual Download Page 136

Page: 136 / 314

136 Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

9.2.4.2 Information

Figure 38: WBM Page, “Port Settings” – “Information” Tab

Table 41: WBM Page, “Port Settings” – “Information” Tab

Port Settings
Parameters

Default

Description

Port

From:

Select a port or port range that you want to display.

To:

Select a port or port range that you want to display.

Description

Port Status
Parameters

Default

Description

Port

1 … 10

This column displays the port numbers.

Description

This column displays the name of the port.

Status

This column displays the status of the port.

Uptime

This column displays the operating mode of the

switch.

Medium Mode

This column displays the connection type.

Copper

Copper wire

Fiber

Fiber optic cable

Pos: 28.8.4 /Serie 852 (ETH ERNET-Z ubehör)/Konfigurieren/Er weiterte Einstell ung en 852- 0303 @ 27\mod_1467880985902_21.docx @ 216298 @ 23455554553455545554554434455545544455533433344344434433334443 @ 1

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands