WAGO 852-1305 Manual Download Page 49

Page: 49 / 314

WAGO-ETHERNET-Zubehör 852

Enhanced Features

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

For “Flow Control”, the switch sends a pause signal in full-duplex mode to the

sending port, causing it to temporarily stop sending signals when the buffer

memory of the receiving port is full.

For “Backpressure Flow Control”, the switch sends a collision signal to the

sending port in half-duplex mode (mimicking a state of packet collision), causing

the sending port to temporarily stop sending signals and to resend the signals later.

Support for “Force Mode”

1000 Base-T does not support “Force Mode”.

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands