WAGO 852-1305 Manual Download Page 288

Page: 288 / 314

288 Appendix

WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

10.3.5 Monitor

10.3.5.1 Alarm

Table 149: CLI “Alarm” Configuration

Node

Command

Description

enable

show alarm-info

This command displays alarm information.

10.3.5.2 Monitor Information

Table 150: CLI “Monitor Information” Configuration

Node

Command

Description

enable

show hardware-monitor

(C|F)

This command displays hardware operation

information.

10.3.5.3 RMON Statistics

Table 151: CLI “RMON Statistics” Configuration

Node

Command

Description

enable

show rmon statistics

This command displays the RMON statistics.

configure

clear rmon statistics

[IFNAME]

This command clears the RMON statistics for one or

all ports.

10.3.5.4 SFP Information

Table 152: CLI “SFP Information” Configuration

Node

Command

Description

enable

show sfp info port

PORT_ID

This command displays the SFP information.

enable

show sfp ddmi port

PORT_ID

This command displays the SFP DDMI status.

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands