manualshive.com logo in svg

WAGO 852-1305, Manual

Share
Download
WAGO 852-1305 Manual Download Page 260

260  Appendix 

WAGO-ETHERNET-Zubehör 852 

 

 

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 

 

Manual 

 

1.1.0  

Pos:  30.6 /Serie 852 (ETH ERNET-Zubehör)/Anhang/CLI- Konfigur ati on @ 26\mod_1465480732374_21.docx @ 212168 @ 23434444444434444444455445444444443444444443444443444444 @ 1 

 

10.3  Configuring in the Command Line Interface (CLI) 

10.3.1  System Status 

10.3.1.1  System Information 

Table 114: CLI “System Information” Configuration 

Node 

Command 

Description 

enable 

show hostname 

This command displays the system’s network name. 

enable 

show interface eth0 

This command displays the current Eth0 

configurations. 

enable 

show model 

This command displays the system information. 

enable 

show running-config 

This command displays the current operating 

configurations. 

enable 

show system-info 

This command displays the system’s CPU utilization 

and memory information. 

enable 

show uptime 

This command displays the system up time. 

 

 

 

Summary of Contents for 852-1305



























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands