u-blox ZED-F9P Interface Description Download Page 62

Page: 62 / 267

u-blox ZED-F9P Interface Description - Manual

Advance Information

CFG-MSG continued

Byte Offset

Number

Format

Scaling

Name

Unit

Description

msgID

Message Identifier

U1[6]

rate

Send rate on I/O Port (6 Ports)

5.9.12.3 Set Message Rate

Message

UBX-CFG-MSG

Description

Set Message Rate

Firmware

Supported on:
•

u-blox 9 with protocol version 27

Type

Get/Set

Comment

This message is deprecated in protocol versions greater than 23.01. Use

instead.

See the

Legacy UBX Message Fields Reference

for the corresponding configuration item.

Set message rate configuration for the current port.

Header

Class

Length (Bytes)

Payload

Checksum

Message Structure

0xB5 0x62

0x06 0x01 3

see below

CK_A CK_B

Payload Contents:

Byte Offset

Number

Format

Scaling

Name

Unit

Description

msgClass

Message Class

msgID

Message Identifier

rate

Send rate on current Port

5.9.13 UBX-CFG-NAV5 (0x06 0x24)

5.9.13.1 Navigation Engine Settings

Message

UBX-CFG-NAV5

Description

Navigation Engine Settings

Firmware

Supported on:
•

u-blox 9 with protocol version 27

Type

Get/Set

Comment

This message is deprecated in protocol versions greater than 23.01. Use

instead.

See the

Legacy UBX Message Fields Reference

for the corresponding configuration item.

Header

Class

Length (Bytes)

Payload

Checksum

Message Structure

0xB5 0x62

0x06 0x24 36

see below

CK_A CK_B

Payload Contents:

Byte Offset

Number

Format

Scaling

Name

Unit

Description

mask

Parameters Bitmask. Only the masked
parameters will be applied. (see

graphic below

)

UBX-18010854 - R04

Advance Information

Page 54 of 259

Summary of Contents for ZED-F9P












































































































































































































































































Search results

Summary of Contents for ZED-F9P

Reviews:

Related manuals for ZED-F9P

Brands by name

Popular brands

u-blox ZED-F9P, Interface Description

Search results

Summary of Contents for ZED-F9P

Reviews:

Related manuals for ZED-F9P

Brands by name

Popular brands