u-blox ZED-F9P Interface Description Download Page 64

Page: 64 / 267

u-blox ZED-F9P Interface Description - Manual

Advance Information

Bitfield mask

This graphic explains the bits of

mask

Name

Description

dyn

Apply dynamic model settings

minEl

Apply minimum elevation settings

posFixMode

Apply fix mode settings

drLim

Reserved

posMask

Apply position mask settings

timeMask

Apply time mask settings

staticHoldMas

Apply static hold settings

dgpsMask

Apply DGPS settings.

cnoThreshold

Apply CNO threshold settings (cnoThresh, cnoThreshNumSVs).

utc

Apply UTC settings.

5.9.14 UBX-CFG-NAVX5 (0x06 0x23)

5.9.14.1 Navigation Engine Expert Settings

Message

UBX-CFG-NAVX5

Description

Navigation Engine Expert Settings

Firmware

Supported on:
•

u-blox 9 with protocol version 27

Type

Get/Set

Comment

This message is deprecated in protocol versions greater than 23.01. Use

instead.

See the

Legacy UBX Message Fields Reference

for the corresponding configuration item.

Header

Class

Length (Bytes)

Payload

Checksum

Message Structure

0xB5 0x62

0x06 0x23 40

see below

CK_A CK_B

Payload Contents:

Byte Offset

Number

Format

Scaling

Name

Unit

Description

version

Message version (2 for this version)

mask1

First parameters bitmask. Only the flagged
parameters will be applied, unused bits must be
set to 0. (see

graphic below

)

mask2

Second parameters bitmask. Only the flagged
parameters will be applied, unused bits must be
set to 0. (see

graphic below

)

U1[2]

reserved1

Reserved

minSVs

#SVs

Minimum number of satellites for navigation

UBX-18010854 - R04

Advance Information

Page 56 of 259

Summary of Contents for ZED-F9P












































































































































































































































































Search results

Summary of Contents for ZED-F9P

Reviews:

Related manuals for ZED-F9P

Brands by name

Popular brands

u-blox ZED-F9P, Interface Description

Search results

Summary of Contents for ZED-F9P

Reviews:

Related manuals for ZED-F9P

Brands by name

Popular brands