u-blox ZED-F9P Interface Description Download Page 10

Page: 10 / 267

u-blox ZED-F9P Interface Description - Manual

Advance Information

Possible lines in the boot screen and their meanings: continued

Entry

Description

FWVER=HPG 1.00

Firmware of product category and version where

SPG

: Firmware of Standard Precision GNSS product

HPG

: Firmware of High Precision GNSS product

ADR

: Firmware of ADR product

UDR

: Firmware of UDR product

TIM

: Firmware of Time Sync product

FTS

: Firmware of Time & Frequency Sync product

PROTVER=27.00

Supported protocol version

GPS;GLO;GAL;BDS

SBAS;IMES;QZSS

ANTSUPERV=AC SD PDoS SR

Configuration of the Antenna supervisor where

: Active Antenna Control enabled

: Short Circuit Detection enabled

: Open Circuit Detection enabled

PDoS

: Short Circuit Power Down Logic enabled

: Automatic Recovery from Short state

PF=FFF00

Product configuration.

The line containing the

FWVER

indicates which version of the firmware is currently running and is

called

firmware version

in the rest of the document.

The numbers in parentheses (revision numbers) should only be used to identify a known firmware
version and are not guaranteed to increase over time.

2.1.2 Decoding the output of UBX-MON-VER (for Protocol Version 24 and above)

Possible fields in UBX-MON-VER and their meanings:

Entry

Description

UBX-18010854 - R04

Advance Information

Page 2 of 259

Summary of Contents for ZED-F9P












































































































































































































































































Search results

Summary of Contents for ZED-F9P

Reviews:

Related manuals for ZED-F9P

Brands by name

Popular brands

u-blox ZED-F9P, Interface Description

Search results

Summary of Contents for ZED-F9P

Reviews:

Related manuals for ZED-F9P

Brands by name

Popular brands