u-blox ZED-F9P Interface Description Download Page 101 | Manualshive

Page: 101 / 267

background image

u-blox ZED-F9P Interface Description - Manual

Advance Information

5.11 UBX-LOG (0x21)

Logging Messages: i.e. Log creation, deletion, info and retrieval.
Messages in the LOG class are used to configure and report status information of the logging and batching
features.

5.11.1 UBX-LOG-CREATE (0x21 0x07)

5.11.1.1 Create Log File

Message

UBX-LOG-CREATE

Description

Create Log File

Firmware

Supported on:
•

u-blox 9 with protocol version 27

Type

Command

Comment

This message is used to create an initial logging file and activate the logging subsystem.

are returned to indicate success or failure.

This message does not handle activation of recording or filtering of log entries (see

Header

Class

ID

Length (Bytes)

Payload

Checksum

Message Structure

0xB5 0x62

0x21 0x07 8

see below

CK_A CK_B

Payload Contents:

Byte Offset

Number

Format

Scaling

Name

Unit

Description

0

U1

-

version

-

The version of this message. Set to 0

1

X1

-

logCfg

-

Config flags (see

2

U1

-

reserved1

-

3

U1

-

logSize

-

Indicates the size of the log:
0 (maximum safe size): Ensures that logging will
not be interrupted and enough space will be left
available for all other uses of the filestore
1 (minimum size):
2 (user defined): See 'userDefinedSize' below

4

U4

-

userDefinedSi

ze

bytes

Sets the maximum amount of space in the
filestore that can be used by the logging task.
This field is only applicable if logSize is set to
user defined.

Bitfield logCfg

This graphic explains the bits of

logCfg

UBX-18010854 - R04

Advance Information

Page 93 of 259

«
...
99
100
101
102
103
...
»

Summary of Contents for ZED-F9P












































































































































































































































































Reviews:

No comments

Related manuals for ZED-F9P

Brand: D-Link Pages: 40

Brand: CAME Pages: 18

Brand: CAME Pages: 28

Brand: CAME Pages: 28

Brand: CAME Pages: 4

Brand: CAME Pages: 40

Brand: CAME Pages: 26

Brand: CAME Pages: 34

Brand: CAME Pages: 2

vlt soft starter mcd 500

Brand: Danfoss Pages: 95

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 33

Brand: Danfoss Pages: 59

Brand: Danfoss Pages: 16

VLT AQUA Drive FC 200

Brand: Danfoss Pages: 91

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 100

Brand: Danfoss Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands