u-blox ZED-F9P Interface Description Download Page 150

Page: 150 / 267

u-blox ZED-F9P Interface Description - Manual

Advance Information

NAV-DOP continued

Byte Offset

Number

Format

Scaling

Name

Unit

Description

0.01

tDOP

Time DOP

0.01

vDOP

Vertical DOP

0.01

hDOP

Horizontal DOP

0.01

nDOP

Northing DOP

0.01

eDOP

Easting DOP

5.14.3 UBX-NAV-EOE (0x01 0x61)

5.14.3.1 End Of Epoch

Message

UBX-NAV-EOE

Description

End Of Epoch

Firmware

Supported on:
•

u-blox 9 with protocol version 27

Type

Periodic

Comment

This message is intended to be used as a marker to collect all navigation messages of an
epoch. It is output after all enabled NAV class messages (except UBX-NAV-HNR) and after
all enabled NMEA messages.

Header

Class

Length (Bytes)

Payload

Checksum

Message Structure

0xB5 0x62

0x01 0x61 4

see below

CK_A CK_B

Payload Contents:

Byte Offset

Number

Format

Scaling

Name

Unit

Description

iTOW

GPS time of week of the

navigation epoch

See the

description of iTOW

for details.

5.14.4 UBX-NAV-GEOFENCE (0x01 0x39)

5.14.4.1 Geofencing status

Message

UBX-NAV-GEOFENCE

Description

Geofencing status

Firmware

Supported on:
•

u-blox 9 with protocol version 27

Type

Periodic/Polled

Comment

This message outputs the evaluated states of all configured geofences for the current
epoch's position.
See the

Geofencing description

for feature details.

Header

Class

Length (Bytes)

Payload

Checksum

Message Structure

0xB5 0x62

0x01 0x39 8 + 2*numFences

see below

CK_A CK_B

Payload Contents:

Byte Offset

Number

Format

Scaling

Name

Unit

Description

iTOW

GPS time of week of the

navigation epoch

See the

description of iTOW

for details.

version

Message version (0x00 for this version)

UBX-18010854 - R04

Advance Information

Page 142 of 259

Summary of Contents for ZED-F9P












































































































































































































































































Search results

Summary of Contents for ZED-F9P

Reviews:

Related manuals for ZED-F9P

Brands by name

Popular brands

u-blox ZED-F9P, Interface Description

Search results

Summary of Contents for ZED-F9P

Reviews:

Related manuals for ZED-F9P

Brands by name

Popular brands