manualshive.com logo in svg

Texas Instruments TMS320DM335, User Manual

Get access to the comprehensive User Manual for the advanced Texas Instruments TMS320DM335, offering detailed instructions and insights to maximize your experience. This essential manual is available for free download exclusively at manualshive.com, empowering you to harness the full potential of your product.

Share
Download
background image

7.6.1.3

Local Reset Emulation Events

7.6.1.4

External Power Control Pending Event

7.6.2 Interrupt Registers

www.ti.com

PSC Interrupts

•

When inhibit sleep is asserted by emulation and software attempts to transition the module out of the
enable state

•

When force active is asserted by emulation and module is not already in the enable state

A local reset emulation event occurs when emulation alters the local reset of a module. Status is reflected
in the EMRST bit in MDSTAT[x]. In particular, a module local reset emulation event occurs under the
following conditions:

•

When assert reset is asserted by emulation although software de-asserted the local reset

•

When wait reset is asserted by emulation

•

When block reset is asserted by emulation and software attempts to change the state of local reset

An external power control pending event occurs during the power domain power on or power off
sequences. The PSC triggers this interrupt as an indication that it is ready for software to apply or remove
power during a power on or power off transition sequence, respectively. Status for this interrupt is
reflected in the EPCx bit in EPCPR. See

Section 7.4.1

for more information.

The external power control pending event occurs when the PSC is pending confirmation that power was
applied to or removed from the power pins. See

Section 7.4.1

for more information.

The PSC interrupt enable bits are: the EMUIHB bit in PDCTLx, the EMUIHB bit in MDCTL[x], the
EMURSTIE bit in MDCTL[x], and the EPx bit in EPCPR.

Note:

To interrupt the ARM, the ARM’s power and sleep controller interrupt (PSCINT) must also be
enabled in the ARM interrupt controller. See

Chapter 8

for more information on the ARM’s

power and sleep controller interrupt and the ARM interrupt controller.

The PSC interrupt status bits are the Mx bit in MERRPR0, the Mx bit in MERRPR1, the Px bit in PERRPR,
the EMUIHB bit in PDSTATx, the EMUIHB bit in MDSTAT[x], the EMURST bit in MDSTAT[x], and the EP
bit in EPCPR. The status bits in MERRPR0, MERRPR1, and PERRPR are read by software to determine
which power domain or which module has generated an emulation interrupt, and then software can read
the corresponding status bits in PDSTATx and MDSTATx to determine which event caused the interrupt.

The PSC interrupt clear bits are the Mx bit in MERRCRx, the Mx bit in PERRCRx, and the EPx bit in
EPCCR.

The PSC interrupt evaluation bit is the ALLEV bit in INTEVAL. When set, this bit forces the PSC interrupt
logic to re-evaluate event status. If any events are still active (if any status bits are set) when the ALLEV
bit in INTEVAL is set to 0x1, the PSCINT is re-asserted to the ARM interrupt controller. Set the ALLEV bit
in INTEVAL before exiting your PSCINT interrupt service routine to ensure that you do not miss any PSC
interrupts while the ARM interrupts are globally disabled.

See

Section 7.7

for complete descriptions of all PSC registers.

SPRUFX7 – July 2008

Power and Sleep Controller

69

Submit Documentation Feedback

Summary of Contents for TMS320DM335













































































































































































Reviews:

No comments

Related manuals for TMS320DM335

Vantron VT-SBC-3399 User Manual preview
VT-SBC-3399
Brand: Vantron Pages: 44
Ebyte E51-470NW16S User Manual preview
E51-470NW16S
Brand: Ebyte Pages: 16
WinSystems LBC- 486Plus Operation Manual preview
LBC- 486Plus
Brand: WinSystems Pages: 98
Aaeon EPIC-BT07 User Manual preview
EPIC-BT07
Brand: Aaeon Pages: 145
IEI Technology PM-PV-N4551/D5251 User Manual preview
PM-PV-N4551/D5251
Brand: IEI Technology Pages: 115
ADLINK Technology NuPRO-780 Series User Manual preview
NuPRO-780 Series
Brand: ADLINK Technology Pages: 43
ADLINK Technology NuPRO-851 User Manual preview
NuPRO-851
Brand: ADLINK Technology Pages: 44
Nuvoton ISD91200 Series Technical Reference Manual preview
ISD91200 Series
Brand: Nuvoton Pages: 473
Nuvoton ISD94100 Series Technical Reference Manual preview
ISD94100 Series
Brand: Nuvoton Pages: 928

Brands by name

Popular brands

Load more brands