Texas Instruments TMS320DM335 User Manual Download Page 128

Page: 128 / 172

9.10.7 BOOTCFG - Boot Configuration

System Control Register Descriptions

www.ti.com

The device boot configuration (the state of the BTSEL[1:0] and AECFG[3:0] signals are captured in the
BOOTCFG register.

Figure 9-6. BOOTCFG - Boot Configuration

Reserved

R-0

Reserved

GIO0_RESET

BTSEL

Reserved

AECFG

R-0

R-1101

LEGEND: R = Read only; -

= value after reset

Table 9-9. BOOTCFG - Boot Configuration Field Descriptions

Bit

Field

Value

Description

31-9

Reserved

GIO0_RESET

GIO0 Value Sampled at Reset Sampled prior to debounce circuit

7-6

BTSEL[2:0]

Configuration at boot of BTSEL[1:0] pins

Take care that AECFG[3:0] settings, which configure AEMIF pin mux settings in PINMUX2[4:0], are
compatible with the boot mode:

- OneNAND boot requires AECFG[3:0] = 0010b

- Only 8_bit NAND boot is supported - AECFG[3:0] = 1XXXb

Boot from ROM - NAND Flash boot mode

Boot from AEMIF - OneNAND

Boot from ROM - SD0 boot mode

Boot from ROM - UART0 boot mode

5-4

Reserved

3-0

OSC_SW[1:2]

AEMIF Configuration settings for boot by AECFG[3:0] pins

[3] - AEMIF Data Bus width (0 = 16-bit, 1 = 8-bit)

[2:1] - Configuration of EM_AN pin

- 00 = BA0, needed for 8-bit ASYNC memories or devices

- 01 = A[14], required for OneNAND operation and AEMIF in Half_Rate mode

- 10 = GIO[54], usable in NAND mode only

- 11 = reserved

[0] - AEMIF Address bus width (0 = A{13:3] and A[0], BA1

Take care that AECFG[3:0] settings, which configure AEMIF pin mux settings in PINMUX2[4:0], are
compatible with the boot mode:

- OneNAND boot requires AECFG[3:0] = 0010b

- Only 8_bit NAND boot is supported _ AECFG[3:0] = 1XXXb

System Control Module

128

SPRUFX7 – July 2008

Submit Documentation Feedback

Summary of Contents for TMS320DM335













































































































































































Search results

Summary of Contents for TMS320DM335

Reviews:

Related manuals for TMS320DM335

Brands by name

Popular brands

Texas Instruments TMS320DM335, User Manual

Search results

Summary of Contents for TMS320DM335

Reviews:

Related manuals for TMS320DM335

Brands by name

Popular brands