Sony Ericsson FOMA SO905iCS, Manual

Page: 528 / 534

27
Command Outline/Parameter Input example
ATS2=<n> Sets an escape character. ATS2=0
ATS2?
n=0-126 43: Default, 0: When the parameter is omitted
[&F] n=127 Disables the escape operation.
ATS3=<n> Sets a carriage return (CR) character that can identify the end of an
AT command character string. It is added to the end of the echoed
back command character string and result code. ATS3=13
ATS3?
[&F] n=13 Default
ATS4=<n> Sets a line feed (LF) character. When the result code is displayed in
alphabets, it is added after the carriage return (CR) character. ATS4=10
ATS4?
[&F] n=10 Default
ATS5=<n> Sets a backspace (BS) character that deletes the last character of
input buffer during AT command input. ATS5=8
ATS5?
[&F] n=8 Default
ATS6=<n> Sets the pause time (seconds) until dialing. Although the register
is set, the operation does not take place even if this command is
used. ATS6=5
ATS6?
[&F] n=2-10 5: Default, when the parameter is omitted
ATS8=<n> Sets the pause time (seconds) until a comma dial is performed.
Although the register is set, the pause time is fixed to 3 seconds
even if this command is used. ATS8=3
ATS8?
[&F] n=1-255 60: Default, 121-255: Assumes 120
ATS10=<n> Sets the automatic disconnection delay time (1/10 seconds).
Although the register is set, the operation does not take place even
if this command is used. ATS10=1
ATS10?
[&F][&W] n=1-255 1: Default, when the parameter is omitted
ATS30=<n> Sets the waiting time (minutes) until communication is disconnected
when no data is exchanged during 64K data communication. ATS30=0
ATS30?
n=0 Does not disconnect (Default, when the parameter is omitted).
[&F] n=1-255 Waiting time (minutes) until communication is disconnected
ATS103=<n> Sets a separator used when originating a call by adding an
incoming call sub-address for 64K data communication. ATS103=0
ATS103?
n=0 ＊ (When the parameter is omitted)
n=1 / (Default)
[&F] n=2 ¥
ATS104=<n> Sets a separator used when originating a call by adding an
outgoing call sub-address for 64K data communication. ATS104=0
ATS104?
n=0 # (When the parameter is omitted)
n=1 % (Default)
[&F] n=2 &
ATV<n> Sets the display method for the result code. ATV1
n=0 Displays the result code using a numeric value (When the
parameter is omitted).
[&F][&W] n=1 Displays the result code using text (Default).
ATX<n> Sets the busy tone and dial tone detection, and communication
speed indication. ATX1
n=0 Without busy/dial tone detection, without speed indication (When
the parameter is omitted)
n=1 Without busy/dial tone detection, with speed indication
n=2 Without busy tone detection, with dial tone detection, without speed
indication
n=3 With busy tone detection, without dial tone detection, with speed
indication
[&F][&W] n=4 With busy/dial tone detection, with speed indication (Default)
ATZ Sets the FOMA terminal settings to the contents of a volatile
memory recorded by AT&W. When this command is executed
during communication, the operation for disconnecting the line is
performed. ATZ
+++ Switches the FOMA terminal from the online data mode to the online
command mode. The escape guard section is fixed to 1 second. +++