Sony Ericsson FOMA SO905iCS, Manual

Page: 527 / 534

26
Command Outline/Parameter Input example
AT+CREG=<n> Sets whether the outside/inside of the service area information is
displayed.
When you enter AT+CREG?, the result is displayed in the “+CREG:
<n>,<stat>” format.
stat=0: Outside of the service area, stat=1: Inside of the service
area (home), stat=4: Unknown, stat=5: Inside of the service area
(visitor) AT+CREG=1
AT+CREG?
AT+CREG=?
n=0 Does not display (Default).
[&F][&W] n=1 Displays.
AT+GMI Displays the name of the FOMA terminal manufacturer. AT+GMI
AT+GMI=?
AT+GMM Displays the name of the FOMA terminal. AT+GMM
AT+GMM=?
AT+GMR Displays the version of the FOMA terminal. AT+GMR
AT+GMR=?
AT+IFC=<n,m> Sets the local flow control method between the PC and the FOMA
terminal.
n is used for setting the control of DCE by DTE while m is used for
setting the control of DTE by DCE. When m is omitted, the same
input value as DCE by DTE is used. AT+IFC=2,2
AT+IFC?
AT+IFC=?
n=0 Does not perform flow control.
n=1 Performs XON/XOFF flow control.
n=2 Performs RS/CS (RTS/CTS) flow control (Default).
m=0 Does not perform flow control.
m=1 Performs XON/XOFF flow control.
[&F][&W] m=2 Performs RS/CS (RTS/CTS) flow control (Default).
AT+WS46=<n> Sets the radio network used by the FOMA terminal when originating
communication. AT+WS46=22
AT+WS46?
AT+WS46=?
[&F][&W] n=22 FOMA network (fixed value)
AT¥S Displays the command setting and S register data. AT¥S
AT¥V<n> Selects whether an extended result code is used when the
connection is established. AT¥V0
n=0 Does not use an extended result code (Default, when the parameter
is omitted).
[&F][&W] n=1 Uses an extended result code.
ATA Performs the receiving operation according to the mode received
by the FOMA terminal.
ATD Originates packet or 64K data communication.
For packet communication: Enter the command in the “ATD
＊ 99 ＊
＊＊ cid#” format. When cid is omitted, cid=1 is set. If the command
is entered in the format beginning with “ATD184 ＊ 99”, then 184
(without caller ID) is added to an APN of the specified cid. (This
condition also applies to 186.)
For 64K data communication: Enter the command in the “ATD
phone number” format.
For originating a call by redial: Enter the command in the “ATDL” or
“ATDN” format.
ATD
＊
99
＊＊＊
3#
ATE<n> Sets whether characters sent from the PC are echoed back. ATE0
n=0 Does not echo back (When the parameter is omitted).
[&F][&W] n=1 Performs an echo back (Default).
ATH Disconnects packet or 64K data communication. ATH
ATI<n> Displays an identification code. ATI0
n=0 Displays “NTT DoCoMo” (When the parameter is omitted).
n=1 Displays the name of the FOMA terminal.
n=2 Displays the version of the FOMA terminal.
ATO Switches from the online command mode to the online data mode
during communication. ATO
ATQ<n> Sets whether the result code is displayed on the PC. ATQ1
n=0 Displays (Default, when the parameter is omitted).
[&F][&W] n=1 Does not display.
ATS0=<n> Sets the number of rings sounded until the FOMA terminal
automatically receives a call. ATS0=0
ATS0?
n=0 Does not automatically receive a call (Default, when the parameter
is omitted).
[&F][&W] n=1-255 Number of rings