SMAY iSWAY-FC Operation And Maintenance Manual Download

Page: 7 / 168

Operation and Maintenance Manual (DTR) iSWAY

Set of products

Version 1.8 of 2.2021

Regulations

2.1.

Placing on the market.

The iSWAY-FC

, iSWAY-WFC

, iSWAY-RFC

compact pressurization unit intended for

smoke and heat control systems (iSWAY-FC

, iSWAY-WFC

, iSWAY-RFC

) has been marketed on

the basis of documents issued by the Building Research Institute (ITB):

NATIONAL TECHNICAL ASSESSMENT ITB-KOT-2018/0565 wydanie 2

NATIONAL CERTIFICATE OF CONSTANCY OF USAGE PERFORMANCE NO 020-UWB-
2737/W

The iSWAY-FC

, iSWAY-WFC

, iSWAY-RFC

compact pressurization unit intended for

smoke and heat control systems is marked by the manufacturer with a construction mark .

SMAY sues iSWAY®

NATIONAL DECLARATION OF PERFORMANCE NO 012-B-2019

Summary of Contents for iSWAY-FC









































































































































































Search results

Summary of Contents for iSWAY-FC

Reviews:

Related manuals for iSWAY-FC

Brands by name

Popular brands

SMAY iSWAY-FC, Operation And Maintenance Manual

Search results

Summary of Contents for iSWAY-FC

Reviews:

Related manuals for iSWAY-FC

Brands by name

Popular brands