SMAY iSWAY-FC Operation And Maintenance Manual Download

Page: 51 / 168

Operation and Maintenance Manual (DTR) iSWAY

Set of products

Version 1.8 of 2.2021

Fig. 11.17. PDA-1 roof base.

On the top side, the base connects to the other modules of the iSWAY-RFC

unit in the same way

as the connection to the ventilation duct. All components of the iSWAY-RFC

unit have flanged

connections to the other modules in corners with screws and MKZ clamps. View of the kit
connection as shown in Fig. 11.18.

Fig. 11.18. iSWAY-RFC

mounted using a PDA base for the brickwork plinth with CPDB air intake.

11.3.2.

iSWAY-RFC

in the horizontal version

The iSWAY-RFC

kit is recommended to be mounted on the BIG FOOT H support system, not

offered as an additional accessory for iSWAY-RFC

. The supports are mounted to the duct sections

of the set in order to support the system. One BIG FOOT H module consists of two feet, two vertical

Summary of Contents for iSWAY-FC









































































































































































Search results

Summary of Contents for iSWAY-FC

Reviews:

Related manuals for iSWAY-FC

Brands by name

Popular brands

SMAY iSWAY-FC, Operation And Maintenance Manual

Search results

Summary of Contents for iSWAY-FC

Reviews:

Related manuals for iSWAY-FC

Brands by name

Popular brands