background image

Low-energy ventilation unit 

with heat recovery

© Vallox
1.09.413E
14.5.2013

1  Extract air fan
2  Supply air fan
3  Post-heating radiator 

 

(electric 900 W) 

4  Heat recovery cell
5  Outdoor air fi lter F7
6  Outdoor air fi lter G4
7  Extract air fi lter G4
8  Automatic summer/winter damper
9  Safety switch
10  Measurement outlets 

 

(behind an opening door)

13  Control panel Digit SED
14  Carbon dioxide sensor (option)
15  Humidity sensor (option)

•   Can replace MUH-Ilmava 

100/120 from 1983–2004 

without ductwork alteration

Code 

A3560

Models

VALLOX 121 SE R

VALLOX 121 SE L

Electrical connection 

 

230 V, 50 Hz, 

 5.7 A

Degree of protection provided by enclosures 

IP 34

Fans direct current  Extract air  0.117 kW 0,9 A 

106 dm

3

/s 100 Pa

(DC) 

Supply air  0.117 kW 0,9 A 

104 dm

3

/s 100 Pa

Heat recovery 

 

 

Cross-counter fl ow cell, 

η

 >80 %

Heat recovery bypass 

 

Automatic

Electric post-heating unit (standard) 

900 W 3.9 A

Fans 

Supply air   

G4 and F7

 

Extract air   

G4

Weight 

 

 

60 kg

Ventilation power adjustment   

– Digit SED controller

 

 

 

– CO

2

 and %RH control

 

 

 

– remote monitoring control (voltage signal)

Options 

 

 

– CO

2

 sensor

 

 

 

– % RH sensor

TECHNICAL DATA

Operating, maintenance and technical instructions

10

13

14

15

1

2

3

4

5

6

8

7

9

The fi gure shows 

the R model

Vallox

121

SE

Summary of Contents for VALLOX 121 SE Series













Reviews: