SMAY iSWAY-FC Operation And Maintenance Manual Download Page 24

Page: 24 / 168

Operation and Maintenance Manual (DTR) iSWAY

Set of products

Version 1.8 of 2.2021

Fig. 5.11. iSWAY-RFC

in horizontal version with SRC-D damper and ZS intake louver.

The second iSWAY-RFC

configuration shown in fig. 5.12 in the horizontal version is without the

SRC-D damper, and the end of the installation and the function of the dumper is performed by an
air intake with moving lamellas CDH-K. In this case, a KCD smoke detector duct installed in front
of or behind the fan is used.

Straight section of the duct
(length: min. 400)

Ventilator assembly

SCR-D damper

CDH-K air intake

Straight section of the duct
(length: min. 400)

Ventilator assembly

Duct with smoke detector KCD

ZS intake louver

Summary of Contents for iSWAY-FC









































































































































































Search results

Summary of Contents for iSWAY-FC

Reviews:

Related manuals for iSWAY-FC

Brands by name

Popular brands

SMAY iSWAY-FC, Operation And Maintenance Manual

Search results

Summary of Contents for iSWAY-FC

Reviews:

Related manuals for iSWAY-FC

Brands by name

Popular brands