Silicon Laboratories EFR32xG14 Wireless Gecko Reference Manual Download Page 643

Page: 643 / 1140

19.5.16 LEUARTn_PULSECTRL - Pulse Control Register (Async Reg)

For more information about asynchronous registers see

4.3 Access to Low Energy Peripherals (Asynchronous Registers)

Offset

Bit Position

0x03C

Reset

0x0

Access

Name

PULSEFIL

PULSEEN

PULSEW

Bit

Name

Reset

Access Description

31:6

Reserved

To ensure compatibility with future devices, always write bits to 0. More information in

1.2 Conven-

tions

PULSEFILT

Pulse Filter

Enable a one-cycle pulse filter for pulse extender

Value

Description

Filter is disabled. Pulses must be at least 2 cycles long for reliable de-
tection.

Filter is enabled. Pulses must be at least 3 cycles long for reliable de-
tection.

PULSEEN

Pulse Generator/Extender Enable

Filter LEUART output through pulse generator and the LEUART input through the pulse extender.

3:0

PULSEW

0x0

Pulse Width

Configure the pulse width of the pulse generator as a number of 32.768 kHz clock cycles.

Reference Manual

LEUART - Low Energy Universal Asynchronous Receiver/Transmitter

silabs.com

| Building a more connected world.

Rev. 1.1 | 643

Summary of Contents for EFR32xG14 Wireless Gecko





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for EFR32xG14 Wireless Gecko

Reviews:

Related manuals for EFR32xG14 Wireless Gecko

Brands by name

Popular brands

Silicon Laboratories EFR32xG14 Wireless Gecko, Reference Manual

Search results

Summary of Contents for EFR32xG14 Wireless Gecko

Reviews:

Related manuals for EFR32xG14 Wireless Gecko

Brands by name

Popular brands