SII IP-6900 User Manual Download

Page: 112 / 266

2-68

Preset use of the edge guard in the ENTRY menu on the

operation panel. The right and left margins of the media

can be controlled by setting on the operation panel.

The right and left margins of the print area will be changed

by 10 mm when the edge guard is used.

(5 mm if not used)

Clean the media edge guard, if dirty. (

⇒

See page 2-83

"Cleaning platen")

The nap that cannot be removed with the media edge guard

causes gaps in printing. Remove it in advance.

NOTES

Mount the media edge guard on the right and left media feed paths
to protect the head from nap and curl of the media edge.

Using the Media Edge Guard

Media edge guards

Media

Media edge guards

(Cap side)

(Wipe side)

[Specifications of media edge guard]

Media thickness: Up to 0.65 mm

The width of the print area decreases when the media

edge guard is used.

The influence of the vacuum fan is eliminated.

HINT

Summary of Contents for IP-6900











































































































































































































































































Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands

SII IP-6900, User Manual

Search results

Summary of Contents for IP-6900

Reviews:

Related manuals for IP-6900

Brands by name

Popular brands