SII IP-6900 User Manual Download | Manualshive

Page: 190 / 266

background image

3-62

(2) Buzzer setting

Sets whether the buzzer sounds when the head is removed from the
cap in routine maintenance or head height adjustment or when the
head cannot be capped due to a paper jam error, etc. during printing.

<Parameter (Enter a choice)>
- ON: Sounds the buzzer.
- OFF: Does not sound the buzzer.

The buzzer set here is an alarm for head protection. The

usual buzzer for an error sounds when an error occurs

regardless of this setting.

(3) Ink end buzzer setting

Sets whether the buzzer sounds when the main cartridge ink is used
up.

<Parameter (Execution form)>
- ON: Sounds the buzzer.
- OFF: Does not sound the buzzer.

The buzzer set here is an alarm for head protection. The

usual buzzer for an error sounds when an error occurs

regardless of this setting.

#BUZZER

>ON

#INKEND BUZZER

>ON

NOTE

NOTE

«
...
188
189
190
191
192
...
»

Summary of Contents for IP-6900











































































































































































































































































Reviews:

No comments

Related manuals for IP-6900

Brand: NCR Pages: 10

Brand: Panasonic Pages: 83

Brand: IBM Pages: 102

WorkCentre Pro 40

Brand: Xerox Pages: 14

Brand: Magicard Pages: 2

Brand: Magicard Pages: 2

Brand: Oki Pages: 1

imageRUNNER 5075

Brand: Canon Pages: 502

imageRUNNER 5075

Brand: Cannon Pages: 268

Brand: Oki Pages: 40

Phaser 6700V/DX

Brand: Xerox Pages: 162

Brand: SATO Pages: 255

Blaster ADVANTAGE

Brand: CognitiveTPG Pages: 20

VersaUV LEF2-300

Brand: Roland Pages: 264

Brand: Oki Pages: 78

Brand: Oki Pages: 2

Brand: Nagel Pages: 22

Small-in-One XP-330

Brand: Epson Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands