SII IP-6900 User Manual Download | Manualshive

Page: 106 / 266

background image

2-62

LCD

Printer Heater ON/OFF key

Printer Heater UP/DOWN key

Front Heater ON/OFF key

Front Heater UP/DOWN key

Rear Heater ON/OFF key

Rear Heater UP/DOWN key

Preset temperature
Current temperature

Changing Heater Control Setting Temperature

In normal use, temperatures of each heater for each selected media
are preset automatically.
Therefore, ON/OFF settings and temperature settings for all heaters
are not necessary.
Use the heater control panel only when the fine adjustment of the
heater temperature is desired.
ON/OFF and temperatures of the three heaters can be set on the
heater control panel individually.

• ON/OFF setting: Use ON/OFF key for each heater.
• Temperature setting: Use the UP/DOWN key for each heater.
• LCD screen: (When the heater is turned ON)

• Upper line: Preset temperature for each heater
• Lower line: Current temperature for each heater
(When the heater is turned OFF)
• “OFF” for each heater on all lines
The preset temperature range is fixed at 15

°

C to

55

°

C.

Regarding menu operation, see

Section 5 “Heater Controller

Menu Operations”.

«
...
104
105
106
107
108
...
»

Summary of Contents for IP-6900











































































































































































































































































Reviews:

No comments

Related manuals for IP-6900

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 72

iPF710 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 92

iPF8000S - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 48

Two-Knife Booklet Trimmer-A1

Brand: Canon Pages: 32

Perfect Binder-C1

Brand: Oce Pages: 82

IMAGERUNNER 7095 PRINTER

Brand: Canon Pages: 615

imageRUNNER C3125i

Brand: Canon Pages: 816

Brand: Keeler Pages: 25

Brand: Samsung Pages: 134

Smart Extruder+

Brand: MakerBot Pages: 7

Brand: Olivetti Pages: 16

Brand: DataCard Pages: 130

V16 Automatic Shaker Unit

Brand: Garment Printer Ink Pages: 21

Brand: Oce Pages: 186

Brand: Savin Pages: 4

Brand: 3nStar Pages: 8

Brand: Oakton Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands